1-1/4” Ball Mount (5” Rise, 10” Length, 3,500 lbs.)

$24.95 $24.95 $24.95

Order by 1pm for delivery today. Orders after 1pm will be delivered tomorrow

Your Address

Please note

  • Not for use in the drop position.

Product Description

Part Number:

Class II Ball Mount for 1-1/4” receiver. 5” rise, not for use in the drop position.

  • Fits 1-1/4" receiver.
  • For 3/4" shank hitch ball.
  • 3,500 lbs gross trailer weight. 300 lbs tongue weight.
  • Black powder coat finish.

Questions & Answers (8)

To view an answer to a question, simply click on the question. To post a new question, click on the "Ask a question" button below.

Ask a Question

*All questions are reviewed and approved before being posted or answered.
Please keep all questions appropriate and related to the product

I have a 2010 Honda Accord Crosstour with a UHaul hitch and 14 height from the ground. Would this item work with my hitch?

–David Yeomans 4/7/2019 4:28:17 PM

Hello, David! Although the ball mount shank may match the hitch receiver diameter, the weight ratings may differ. Your hitch system is only as strong as its lowest-rated component (Hitch, ball mount, ball). I hope that is helpful!

–Savannah 4/26/2019 4:31:18 PM

Would this ball mount be appropriate for a 2007 Honda Odyssey? The one I was given from your installer is too low for my trailer. I need a higher rise.

–Robin 8/4/2018 5:24:40 PM

Hi, Robin! This ball mount will work on a 2007 Honda Odyssey equipped with a 1-1/4" receiver hitch. Thanks for asking!

–Savannah 9/6/2018 2:35:04 PM

This ball mount has the rise that I need, but I am concerned as to whether it is long enough to clear the bumper on my 2013 Nissan Sentra. Can you tell me what the horizontal measurement is between the center of the mounting pin hole and the inside of the vertical portion of the bar? I need a minimum length of 7" from the center of the mounting pin hole to the inside of the vertical portion of the bar. NOTE: This bar would be used on a U-Haul receiver hitch, which I had installed today at your store in East Madison, Wisconsin. Thank you.

–David Van Lanen 7/18/2018 2:52:51 PM

Hey, David! The length from the pin hole to the vertical part of the bar is 7.375 inches. I hope that is helpful!

–Savannah 8/23/2018 8:36:00 AM

Is hitch receiver 36065, 5 inch rise okay to use on a 2011 Altima 4 door with uhaul hitch part # 24737

–George Napier 6/25/2018 6:20:30 AM

Hi, George! The 36065 1-1/4" ball mount will fit into the 24737 1-1/4" receiver. Please note: your hitch system is only as strong as its lowest rated component.. Thank you!

–Savannah 7/23/2018 10:57:48 AM

what is the proper drawbar to use with a 2017 ford fusion 2.0 AWD? 3.5 or 5 inch rise? Is it available in store?.

–Tom Black 8/9/2017 12:38:12 AM

what is the proper drawbar to use with a 2012 ford fusion se? 3.5 or 5 inch rise.

–Greg 6/4/2017 5:24:51 PM

Hi, Greg! U-Haul ball mount part number 3594 matches your needs (Class l, 1-1/4", 2000 lbs, w/ 3/4" ball hole, 10" Length x 4" rise). Please visit your nearest U-Haul Hitch Location for purchase. Thank you!

–Savannah 7/13/2017 10:58:18 AM

Is the 5 inch riser for 1-1/4 inch hitch available in store?

–Rob Schleinitz 5/1/2017 6:06:39 AM

Hi, Rob! This specific ball mount is not available in store. Please contact your local U-Haul Hitch Center to see what they have in stock for your vehicle.

–Savannah 5/30/2017 9:38:12 AM

Will a ball hitch work with a 2017 Audi Allroad station wagon? If so is one type better for the car's construction than another?

–Elizabeth Lamont 12/15/2016 8:45:36 AM

Currently there are no aftermarket hitch products available for your vehicle. We can expect to see more information by February of 2017. If you are in need of a hitch before then, please visit this page and enter your vehicle information for a possible free custom built hitch.

–TIMOTHY 12/19/2016 10:43:28 AM

Recommended Items