How to Install a Trailer Hitch on a Chevrolet Blazer

Adding a trailer hitch to a Chevrolet Blazer requires only a few tools, a CURT 13418 trailer hitch, and a short amount of time to complete the installation. This trailer hitch and installation process will work for the Chevrolet Blazer model years 2019 - 2024.

Follow these basic steps to begin hauling trailers and other kinds of hitch-mounted accessories for your Chevrolet Blazer today.

Tools needed:

  • Safety Glasses
  • Torque 15 Bit
  • Exhaust Strap
  • Exhaust Pliers
  • 15mm Wrench
  • Torque Wrench
  • Power Drill
  • Step Bit
  • 19mm Socket
  • 4” Extension

2019-2024 Chevrolet Blazer Hitch Installation Steps

1. Remove Rear Access Panel

The first step in our hitch installation process will be to remove the rear access panel found on the vehicle. To do this, we will need to remove its two wing nuts which can be done by hand. Following this, we are going to remove two more screws using our 15-bit and power drill.

2. Lower the Exhaust

Our next step will be to lower the vehicle’s exhaust to make room for the hitch to be installed. Before we begin to lower, we will install an exhaust strap to support its weight.

Two bolts need to be removed on the exhaust hanger on each side of the vehicle, which can be done with a torque wrench. With the bolts removed, we can now disconnect these exhaust brackets and remove the rubber isolator.

3. Enlarge Access Holes

To allow the provided hardware to be correctly installed, we will need to enlarge the access holes found on the vehicle’s frame. Using our step bit, we will enlarge the middle access hole on each side of the car.

4. Install Hardware

With our access holes ready, we can now use the fishwire method to install our provided hardware into the vehicle’s frame. Carriage bolts with a spacer will be installed on each side of the vehicle.

5. Raise Hitch Into Place

Now we are going to bring our hitch into place, aligning the attachment holes of the hitch with the access holes on the vehicle’s frame.

During this process, be sure to feed the fish wire through each hitch attachment point and install the flange nut to each bolt. 

6. Tighten and Torque Hitch

With the hitch in place, we can now tighten and torque the hitch according to the manufacturer’s specifications to properly secure it to the vehicle’s frame. We will be using a 19mm socket to complete this step.

7. Re-Install Exhaust and Rear Access Panel

Now that our hitch is installed, we will complete this process by re-installing the lowered exhaust and the rear access panel we previously removed.

You should now have your trailer hitch installed on your Chevrolet Blazer.

How Much Does it Cost to Add a Hitch for a 2019-2024 Chevrolet Blazer?

The price range of a hitch for a Chevrolet Blazer ranges from $200 to $250. U-Haul carries several different classes of hitches and offers different sizes to accommodate both 1¼ to 2-inch receivers. U-Haul offers both installation services at a local U-Haul Moving Center® and will ship your hitch to your home.

How Much Does a Hitch for a 2019-2024 Chevrolet Blazer Cost?

Installation costs are normally $100 to $200 but you should check with your local U-Haul Moving Center® as prices can differ based on location, the hitch model you are installing, and your vehicle. All U-Haul Moving Centers can install a hitch to your vehicle and with over 1,500 U-Haul centers throughout the country, you can have your hitch installed and be back on the road in no time.

All trailer hitches sold and installed at a U-Haul Moving Center® come with the option of a lifetime warranty plan guaranteed to replace your hitch with no limitation for any damage, including collision, corrosion, accidental overload, jackknifing, and vehicle theft.

Chevrolet Blazer Hitch Prices

How Long Does it Take to Install a Hitch on a 2019-2024 Chevrolet Blazer?

Installation takes anywhere from 1 to 2 ½ hours depending on the hitch being installed and your vehicle. We recommend making an online appointment from our website to accommodate your busy schedule. In addition, U-Haul service centers offer an extensive line of towing accessories (Ball mount, Hitch ball, Pin, and Clip, Wiring) to help you safely tow your boat, camper, or trailer. 

Do You Need a Wiring Kit for a 2019-2024 Chevrolet Blazer?

If you are planning to tow a trailer or camper with brake lights, running lights, and turn signal, you will want a wiring kit to power the lights on your trailer. The most common lighting harness comes in a 4 pin and 7 pin connector.  The 4- way connector has basic lighting functions (running lights, brake lights, turn signal) while the 7-way connector adds a 12-volt circuit, circuit for electric trailer brakes, and reverse lights. U-Haul offers both 4-way and 7-way connectors.  Find out which option is best for your Chevrolet Blazer. 

Wiring Kits for 2019-2024 Chevrolet Blazer



Back
To Top